Now more and more people began to buy tents in order to install them in their country house, site. The thing is good and necessary. The tent itself is good, but the frames that go with it are very flimsy and are designed only to stand somewhere in a room where there are no winds and rains. This makes the purchase of a tent worthless and useless. The frame of thin metal tubes breaks and collapses at the first winds and strong rains. And in order to get out of this situation you will have to build a frame with your own hands.
How to make a wooden frame for a tent
The most affordable will be a wooden frame. If you do it correctly, then it will stand for a long time, it will be a reliable and strong structure. The frame will consist of racks, and installed on a wooden podium. Therefore, for the construction you will need boards, with a thickness of at least 30 mm and bars of which are 50 by 30 mm (you can a little more or slightly smaller), a few more bars on corner racks in a size of 50 by 100 mm. For the catwalk, logs or bars of coniferous wood of wood will also be required.
Having estimated where the future tent will stand, it is necessary to level the site, and make a thorough measure of the podium. It should be larger than the tent itself, both in length and in width. Since the frame itself will stand on this podium.
After you need to put the beds and pin the boards to them (this will be floor). By closing the side parts, you can start installing the frame. First of all, you should remove the exact dimensions from the frame that was along with the tent.
This is exactly what it is necessary to build.
Start building a structure with corner racks. They must be reliably screwed to the podium floor with metal corners and associated with a securely nailed, also to the floor, board. Corner racks should stand reliably, since the whole load will hang on them.
How to make a wooden frame for a tent
The next step will be screwing the rails along the upper perimeter. Reiki should be attached with a flush racks using metal strips with holes for screws.
How to make a wooden frame for a tent
Then you can make an extension. First, transverse are placed from the upper racks and attached to the floor. Then we fasten the corner racks with the help of bars so that they do not dangle and stand tight. The bottom of the rails rests on the floor and transverse rails. Such an extension will provide the strength of the structure. All fasteners are made using metal corners and strips that are screwed to self -tapping screws.
A very reliable design can turn out that can withstand heavy loads.
Now it is necessary to start the most responsible work – the installation of the roof. This will take the most time and require significant efforts and skills.
She will also be from the same racks. First of all, the horse is installed. It is chopped in size on the ground, set in place and attached to the transverse upper rails. After that, it is necessary to fit and attach to the skate of the rails going to the corner racks. Screw everything to self -tapping screws, if necessary, use metal strips. The result should be a skeleton of the roof. It will consist of a skate holding at the expense of the rails going to the corners and two on each long side of the top of the frame. Due to the exact measurement, the skeleton of the roof should stand tightly, since the slats will be reliably rifled and screwed up.
How to make a wooden frame for a tent
The latest stage of the roof installation will be the skeleton extensions with longitudinal rails. They are needed so that the tent lay on the roof, and rain water could easily drain from it. In addition, the extension will give the roof additional strength. It is best to fasten several rails on each side. The distance between them should be such that you could then crawl between them (this will have to be done when screwing, as well as during the installation of the tent and its removal). At the same time, it is advisable to strive as much as possible as possible.
After the roof is ready, you can proceed to the final stage of construction. It is necessary to strengthen the additional rail all the vertical rails-strokes, screwing them to each other. Then twist all the sharp corners and ribs. This is in order not to tear the tent later.
So that the frame does not rot, it is recommended to paint it with biox.
How to make a wooden frame for a tent
The frame is ready to use.
